The Best Torsion Spring For Liftmaster

All DURA-LIFT torsion springs are manufactured from Class 2 high-tensile, oil-tempered spring wire, meeting ASTM A229. All of our torsion spring wire is coated for improved corrosion resistance and easier handling. Both 10,000 “standard” cycle and 25,000 “high-cycle” springs are available in left or right wind, and in precut or longer lengths. Both the winding and stationary cones are professionally installed for safe operation. Two 12-inch winding rods are included with all orders. Torsion springs are designed to lift specific weights and should be replaced with springs of the same size and wire gauge. Make sure to determine your wire gauge, inner diameter, and coil length.

TECHNICAL DETAILS:

• .250 wire gauge
• 35″ coil-to-coil length
• 2″ inner spring diameter
• 1x left-hand wind and 1x right-hand spring included
• 2x winding bars included

DURA-LIFT™ 100% SATISFACTION GUARANTEE:

DURA-LIFT™ products are distributed exclusively by WESSOL and are warranted against defects or failures for one year from the purchase date. Should you incur a defect or failure during this period, WESSOL will assist you or replace the product(s) at no additional cost.

Need Application Help?

We know that you want to be sure that you are replacing the correct garage door hardware! If you have any questions about this product’s compatibility for your specific application, please reach out and ask our experts!

DASMA WARNING:

HIGH SPRING TENSION CAN CAUSE SERIOUS INJURY OR DEATH. DO NOT adjust, repair or remove springs or parts to which springs are connected, such as steel brackets, cables, wood blocks, red colored fasteners or other parts of the counterbalance system. Adjustments or repairs must ONLY be made by a trained door systems technician using proper tools and instructions.

WARNING: Torsion springs, extension springs, and related door hardware can causeserious injury or death if not handled and installed properly.Professional installation isrecommended.Do NOT attempt to install springs or hardware yourself unless you have the proper tools, reasonablemechanical aptitude and experience, and upper arm strength.Read and understand all instructionsbefore you begin work.Extension and torsion springs, along with attached hardware, are under extreme tensionat all times. All tension must be released from springs before any work is performed.

WARNING: Torsion springs, extension springs, and related door hardware can causeserious injury or death if not handled and installed properly.Professional installation isrecommended.Do NOT attempt to install springs or hardware yourself unless you have the proper tools, reasonablemechanical aptitude and experience, and upper arm strength.Read and understand all instructionsbefore you begin work.Extension and torsion springs, along with attached hardware, are under extreme tensionat all times. All tension must be released from springs before any work is performed.

Product Description

Use this steel left hand wound torsion spring to replace broken garage door springs. It includes stationary and winding cones with .243” wire size x 2 “ inside dimension x 32” length with yellow color code. This torsion spring is a regular duty spring with an estimated lifetime rating of 10,000 cycles. These types of torsion springs provide lifting force for heavy garage doors and must be selected by the spring’s dimensions, rather than the door’s weight. See the product specifications with illustrations found in Prime-Line’s Torsion Spring Selection Guide to assure that the proper replacement spring has been selected. Steel winding rods are used to wind and unwind the tension on torsion springs and they are the only tools recommended for this purpose. Two winding rods are required for torsion spring replacement. When dual spring installations are involved, it is important to correctly install both the left and right wind springs during the same job. In the case of dual spring installations, note that the proper use of LEFT WIND and RIGHT WIND springs is imperative. Also, when dual spring installations are involved, it is important to replace both springs, as replacing only one spring may add increased strain to the older non-replaced spring. As an important safety precaution: all broken or malfunctioning hardware should be replaced with matching hardware, without any modifications. Garage door torsion springs can cause serious injury if not handled and installed properly. If attempting to replace the torsion springs yourself, it is important that the removal or adjustment of torsion springs is not attempted with any other tool other than Prime-Line’s item number GD-52238. Failure to utilize Prime-Line’s item number GD-52238 for the replacement of these springs may result in severe personal injury. Note: To determine the handing of your torsion spring wind, look at the end of the spring with the ‘finger’ of the spring at the top of the wind. When the end of the spring is at 12:00 o’clock and it is pointing to the left, the spring is a right wind; if the end of the spring points to right (positioned at 12:00 o’clock) it is a left wind. When standing inside the garage looking outside, the torsion spring with the black painted winding cone installs on the right side of the door, and the torsion spring with the red painted winding cone installs on the left side of the door.

From the Manufacturer

This torsion spring is constructed of steel and it includes a stationary cone and a winding cone attached to opposite ends of the spring. These types of torsion springs provide lifting force for heavy garage doors and must be selected by the spring’s dimensions, rather than the door’s weight. See the product specifications with illustrations found in Prime-Line’s Torsion Spring Selection Guide to assure that the proper replacement spring has been selected. In the case of dual spring installations, note that the proper use of LEFT WIND & RIGHT WIND springs is imperative. Also, when dual spring installations are involved, it is important to replace both springs, as replacing only 1 spring may add increased strain to the older non-replaced spring. This torsion spring is a regular duty spring with an estimated lifetime rating of 10,000 cycles. As an important safety precaution: all broken or malfunctioning hardware should be replaced with matching hardware, without any modifications. These garage door torsion springs can cause serious injury if not handled and installed properly. If attempting to replace the torsion springs yourself, it is important that the removal or adjustment of torsion springs is not attempted with any other tool other than Prime-Line’s item number GD-52238. Failure to utilize Prime-Line’s item number GD-52238 for the replacement of these springs may result in severe personal injury. These winding rods are used to wind and unwind the tension on torsion springs and they are the only tools recommended for this purpose. Note: To determine the handing of your torsion spring wind, look at the end of the spring with the ‘finger’ of the spring at the top of the wind. When the end of the spring is at 12:00 o’clock and it is pointing to the left, the spring is a right wind; if the end of the spring points to right (positioned at 12:00 o’clock) it is a left wind. When standing inside the garage looking outside, the torsion spring with the black painted winding cone installs on the right side of the door, and the torsion spring with the red painted winding cone installs on the left side of the door.

Product Description

This torsion spring is constructed of steel and it includes a stationary cone and a winding cone attached to opposite ends of the spring. These types of torsion springs provide lifting force for heavy garage doors and must be selected by the spring’s dimensions, rather than the door’s weight. See the product specifications with illustrations found in Prime-Line’s Torsion Spring Selection Guide to assure that the proper replacement spring has been selected. In the case of dual spring installations, note that the proper use of LEFT WIND & RIGHT WIND springs is imperative. Also, when dual spring installations are involved, it is important to replace both springs, as replacing only 1 spring may add increased strain to the older non-replaced spring. This torsion spring is a regular duty spring with an estimated lifetime rating of 10,000 cycles. As an important safety precaution: all broken or malfunctioning hardware should be replaced with matching hardware, without any modifications. These garage door torsion springs can cause serious injury if not handled and installed properly. If attempting to replace the torsion springs yourself, it is important that the removal or adjustment of torsion springs is not attempted with any other tool other than Prime-Line’s item number GD-52238. Failure to utilize Prime-Line’s item number GD-52238 for the replacement of these springs may result in severe personal injury. These winding rods are used to wind and unwind the tension on torsion springs and they are the only tools recommended for this purpose. Note: To determine the handing of your torsion spring wind, look at the end of the spring with the ‘finger’ of the spring at the top of the wind. When the end of the spring is at 12:00 o’clock and it is pointing to the left, the spring is a right wind; if the end of the spring points to right (positioned at 12:00 o’clock) it is a left wind. When standing inside the garage looking outside, the torsion spring with the black painted winding cone installs on the right side of the door, and the torsion spring with the red painted winding cone installs on the left side of the door.

From the Manufacturer

This torsion spring requires the use of two winding rods. It comes in a white finish with a .250 wire size and a 1-3/4 in. inside diameter. It features a left handed wind with and 32 in. length.

WARNING: Torsion springs, extension springs, and related door hardware can causeserious injury or death if not handled and installed properly.Professional installation isrecommended.Do NOT attempt to install springs or hardware yourself unless you have the proper tools, reasonablemechanical aptitude and experience, and upper arm strength.Read and understand all instructionsbefore you begin work.Extension and torsion springs, along with attached hardware, are under extreme tensionat all times. All tension must be released from springs before any work is performed.

WARNING: Torsion springs, extension springs, and related door hardware can causeserious injury or death if not handled and installed properly.Professional installation isrecommended.Do NOT attempt to install springs or hardware yourself unless you have the proper tools, reasonablemechanical aptitude and experience, and upper arm strength.Read and understand all instructionsbefore you begin work.Extension and torsion springs, along with attached hardware, are under extreme tensionat all times. All tension must be released from springs before any work is performed.

WARNING: Torsion springs, extension springs, and related door hardware can causeserious injury or death if not handled and installed properly.Professional installation isrecommended.Do NOT attempt to install springs or hardware yourself unless you have the proper tools, reasonablemechanical aptitude and experience, and upper arm strength.Read and understand all instructionsbefore you begin work.Extension and torsion springs, along with attached hardware, are under extreme tensionat all times. All tension must be released from springs before any work is performed.