Top 10 Samsung Dryer Will Not Heat

Nowadays, there are so many products of samsung dryer will not heat in the market and you are wondering to choose a best one.You have searched for samsung dryer will not heat in many merchants, compared about products prices & reviews before deciding to buy them.

You are in RIGHT PLACE.

Here are some of best sellings samsung dryer will not heat which we would like to recommend with high customer review ratings to guide you on quality & popularity of each items.

884 reviews analysed

1. DC47-00019A Dryer Heating Element for Samsung Dryers & DC47-00018A Thermostat & DC96-00887A and DC47-00016A Thermal Fuse & DC32-00007A Thermistor Kit 5300W 240V Replace 35001247 2068550 AP4201899

DC47-00019A Dryer Heating Element for Samsung Dryers & DC47-00018A Thermostat & DC96-00887A and DC47-00016A Thermal Fuse & DC32-00007A Thermistor Kit 5300W 240V Replace 35001247 2068550 AP4201899

Feature

2. Dryer Heating Element for Samsung DC47-00019A & DC47-00018A DC96-00887A DC47-00016A Thermal Fuse Kit fits DV48H7400EW/A2 DV40J3000EW/A2 DV45H7000EW/A2 DV52J8700EP/A2 DV448AEP DV419AEW DV50F9A6EVW/A2

Dryer Heating Element for Samsung DC47-00019A & DC47-00018A DC96-00887A DC47-00016A Thermal Fuse Kit fits DV48H7400EW/A2 DV40J3000EW/A2 DV45H7000EW/A2 DV52J8700EP/A2 DV448AEP DV419AEW DV50F9A6EVW/A2

Feature

Description

The instructions work for most Samsung dryers, some may have some small differences. Here is how to replace the DC47-00019A heating element:

STEP1: Shut off the power to the dryer before working on it.
STEP2: Remove the two screws securing the top panel to the back of the dryer. Slide the top panel towards the back of the dryer to remove. You will need to remove the front control panel, some model have screws securing this. Remove them and pull up to remove, you should have enough extra wire to set the control panel on top of the dryer to get it out of the way. if not, then disconnect the wires and set it off to the side. Behind where the control panel was there will be four screws that secure the front panel of the dryer to the frame. Remove these four screws.
STEP3: Open the door of the dryer, there will be two screws that need to be removed at the bottom of the door frame area. With those two screws removed you should be able to tilt the front panel forward, remove the connector to the door switch, and remove the front panel.
STEP4: The heating element is located on the bottom right side of the dryer. To remove the element you will need to remove the wires to the heating element, thermal fuse, and thermostat. Then remove the mounting screw in the front and the whole heating element assembly should pull out the front of the dryer.
STEP5: Remove assembly and replace the DC47-00019A heating element. To re-install the heating element you will need to put everything back in the reverse order. To test the heating element, you will need an Ohm meter or multi-meter. A good heating element should read approximately 9-10 ohms. A burned out element will have an infinite resistance, it won’t register anything.

3. KONDUONE Ultra Durable 4 Inch 8 Feet Clothes Dryer Vent Hose -Fits for Whirlpool Kenmore Maytag Electrolux LG GE Samsung Washer Dryer Transition Ducting Flex Aluminum Exhaust Pipe

KONDUONE Ultra Durable 4 Inch 8 Feet Clothes Dryer Vent Hose -Fits for Whirlpool Kenmore Maytag Electrolux LG GE Samsung Washer Dryer Transition Ducting Flex Aluminum Exhaust Pipe

Feature

4. DC47-00019A Dryer Heating Element Replacement for Samsung, Whirlpool 35001247 by TOPEMAI

DC47-00019A Dryer Heating Element Replacement for Samsung, Whirlpool 35001247 by TOPEMAI

Feature

Description

DC47-00019A Dryer Heating Element has 5/16″ male terminals. 

It is rated 5300 Watts, 240 Volts. 

This part is compatible with the following models: 

DV50F9A8EVP/A2-01,

DV50F9A7EVP/A2-00,

DVE50M7450P/A3-00,

DV484ETHAWR/A1-01,

DV42H5200EP/A3-00,

DV42H5400EW/A3-00,

DV433ETGJWR/A1-00,

DV456ETHDSU/AA-00,

DVE45N5300W/A3-00,

DVE45N5300F/A3-00,

DV45H7000EW/A2-00,

DV45H7000EW/A2-01,

DV45H7000EW/A2-02,

DV484ETHASU/A1-01,

DV48H7400EP/A2-00,

DV410AEW/XAA,

DV328AEW/XAA-00,

DV328AEW/XAA-01,

DV328AEG/XAA,

DV330AEW/XAA-00,

DV330AEW/XAA-01,

DV337AEG/XAA-00,

DV338AEB/XAA-00,

DV393ETPARA/A1-01,

DV395ETPARA/A1-00,

40289032011,

40289032012.

Replace part Numbers: 

2068550, 35001247, 35001119, 1185561,

MDE6700AYW, MDE6700AZW, MDG6700AWM,

MDG6700AWW, NED7200TW10, YIED7200TW10,

PS4205218,PS2038533,TJDC47-00019A, B001ICYB2M,

AP4045884,  AH2038533, EA2038533,  ERDC47-00019A.

Compatible Brands: Samsung, Whirlpool, Kenmore, Hotpoint, General Electric.

You will get: 1  Dryer Heating Element

5. DC47-00018A Dryer High Limit Thermostat Replacement for Samsung & Kenmore Dryers Replace # 35001092 503497 AP4201898 AP6008682 PS11741822 PS4205217

DC47-00018A Dryer High Limit Thermostat Replacement for Samsung & Kenmore Dryers Replace # 35001092 503497 AP4201898 AP6008682 PS11741822 PS4205217

Feature

Description

Specification:
Brand: BTNTVEN
Condition: 100% Brand New and never used
Package Includes:
1 x DC47-00018A Dryer Thermostat

KONDUONE always offer the best customer service to his customers. If you have any problem about your order,please feel free to contact us.

6. Supplying Demand DC97-14486A Clothes Dryer Heating Element Compatible W/Samsung

Supplying Demand DC97-14486A Clothes Dryer Heating Element Compatible W/Samsung

Feature

Description

DC97-14486A Complete Heater Element Assembly. Includes heater casing, heater element, thermostat, and high limit. * The hi-limit which is included has been removed and placed in a protected bag for shipping protections against damages. The hi-limit will need to be reattached once you receive the package. The reason for this has been bent spades and damages of the hi-limit from past shipments. *This is not a Whirlpool and/or a Samsung OEM product. The Whirlpool and/or a Samsung brand names and logos are the registered trademarks of their respective owners. Any use of the Whirlpool and/or a Samsung brand name or model designation for this product is made solely for purposes of demonstrating compatibility. “The trademarks, logos, and service marks (collectively the “Trademarks”) displayed herein Supplying Demand are registered and unregistered trademarks of Supplying Demand, its affiliates, and others. Nothing contained herein should be construed as granting, by implication, estoppel, or otherwise, any license or right to use any trademark displayed herein without the written permission of Supplying Demand or such third party that may own the trademark displayed herein. Your misuse of the trademarks displayed herein, or any other content on this website, except as provided herein, is strictly prohibited.”

7. DC97-14486A Dryer Heating Element Assembly Replacement for Samsung Includes DC47-00019A Heater Element, DC47-00018A Thermostats DC96-00887A Thermal Fuse Replace DC97-08891A DC9714486A DC97-14486D

DC97-14486A Dryer Heating Element Assembly Replacement for Samsung Includes DC47-00019A Heater Element, DC47-00018A Thermostats DC96-00887A Thermal Fuse Replace DC97-08891A DC9714486A DC97-14486D

Feature

Description

The instructions work for most Samsung dryers, some may have some small differences. Here is how to replace the DC97-14486A heating element:

STEP1: Shut off the power to the dryer before working on it.
STEP2: Remove the two screws securing the top panel to the back of the dryer. Slide the top panel towards the back of the dryer to remove. You will need to remove the front control panel, some model have screws securing this. Remove them and pull up to remove, you should have enough extra wire to set the control panel on top of the dryer to get it out of the way. if not, then disconnect the wires and set it off to the side. Behind where the control panel was there will be four screws that secure the front panel of the dryer to the frame. Remove these four screws.
STEP3: Open the door of the dryer, there will be two screws that need to be removed at the bottom of the door frame area. With those two screws removed you should be able to tilt the front panel forward, remove the connector to the door switch, and remove the front panel.
STEP4: The heating element is located on the bottom right side of the dryer. To remove the element you will need to remove the wires to the heating element, thermal fuse, and thermostat. Then remove the mounting screw in the front and the whole heating element assembly should pull out the front of the dryer.
STEP5:To re-install the heating element you will need to put everything back in the reverse order. To test the heating element, you will need an Ohm meter or multi-meter. A good heating element should read approximately 9-10 ohms. A burned out element will have an infinite resistance, it won’t register anything.

8. DC97-14486A Dryer Heating Element Assembly Replacement for Samsung Includes DC47-00019A Heater Element, DC47-00018A Thermostats DC96-00887A Thermal Fuse Replace DC97-08891A DC9714486A DC97-14486D

DC97-14486A Dryer Heating Element Assembly Replacement for Samsung Includes DC47-00019A Heater Element, DC47-00018A Thermostats DC96-00887A Thermal Fuse Replace DC97-08891A DC9714486A DC97-14486D

Feature

Description

The instructions work for most Samsung dryers, some may have some small differences. Here is how to replace the DC97-14486A heating element:

STEP1: Shut off the power to the dryer before working on it.
STEP2: Remove the two screws securing the top panel to the back of the dryer. Slide the top panel towards the back of the dryer to remove. You will need to remove the front control panel, some model have screws securing this. Remove them and pull up to remove, you should have enough extra wire to set the control panel on top of the dryer to get it out of the way. if not, then disconnect the wires and set it off to the side. Behind where the control panel was there will be four screws that secure the front panel of the dryer to the frame. Remove these four screws.
STEP3: Open the door of the dryer, there will be two screws that need to be removed at the bottom of the door frame area. With those two screws removed you should be able to tilt the front panel forward, remove the connector to the door switch, and remove the front panel.
STEP4: The heating element is located on the bottom right side of the dryer. To remove the element you will need to remove the wires to the heating element, thermal fuse, and thermostat. Then remove the mounting screw in the front and the whole heating element assembly should pull out the front of the dryer.
STEP5:To re-install the heating element you will need to put everything back in the reverse order. To test the heating element, you will need an Ohm meter or multi-meter. A good heating element should read approximately 9-10 ohms. A burned out element will have an infinite resistance, it won’t register anything.

9. Farberware FMO11AHTBKD 1.1 Cu. Ft. 1000-Watt Microwave Oven with LED Lighting Cubic Feet, White/Platinum

Farberware FMO11AHTBKD 1.1 Cu. Ft. 1000-Watt Microwave Oven with LED Lighting Cubic Feet, White/Platinum

Feature

Description

Color:White/Platinum

The Farberware classic microwave delivers power, style and convenience with a sleek design to complement your kitchen. Features include 10 power levels and a memory function that stores and recalls your preferred cooking settings. The Farberware classic offers an easy to operate digital interface with 1-6 minute express cook buttons, time or weight based defrost controls, a +30-Seconds control, as well as six pre-programmed cooking functions for popcorn, pizza, a dinner plate and more. Multi-stage cooking means that you can set the power level to adjust during the cooking cycle for perfect results without interruption. The LED display provides a clock and kitchen timer. With a generous 1. 1 Cubic foot cooking Capacity, 1000 watts of power, and a rotating turntable, the Farberware classic is the perfect multi-tasker for your kitchen.

10. KONDUONE 338906 Flame Sensor for Whirlpool Kenmore Maytag Dryer – Replaces WP338906, AP6008294, 14205529, 3-3377, DC32-00008A Gas Dryer Radiant Flame Sensor

KONDUONE 338906 Flame Sensor for Whirlpool Kenmore Maytag Dryer - Replaces WP338906, AP6008294, 14205529, 3-3377, DC32-00008A Gas Dryer Radiant Flame Sensor

Feature

Description

Part Information
WP338906 Dryer Flame Sensor Replacement
Senses heat from the igniter allowing gas valve to open
Used for many gas clothes dryers
Made of both plastic and metal

Repair symptoms
No heat or not enough heat
Takes too long to dry
Shuts off too soon
Will Not Start
Note: This is a guideline only, as other items may cause the same symptoms.

Replaces Part Number
WP338906, 338906, AP6008294, 14205529, 14210083, 3-3377, DC32-00008A, DE353, PS11741429, WP338906VP, EAP11741429, PD00002361, etc.
Please check your appliance model and confirm the compatibility before ordering.

Compatible Brands
Admiral, Amana, Caloric, Crosley, Estate, Inglis, Jenn Air, Kenmore, Kitchen Aid, Magic Chef, Maytag, Norge, Roper, Speed Queen, Whirlpool, etc.

Exact replacement for most Gas Dryers.

Installation tips
Disconnect all power before servicing.
Lift the main top of the dryer and the front panel to access the part

Any question please contact us and we promise to work hard to help you to solve this problem.

Conclusion

By our suggestions above, we hope that you can found Samsung Dryer Will Not Heat for you.Please don’t forget to share your experience by comment in this post. Thank you!